ICF
Wall
9 Things
You Need To Know About Building With Insulating Concrete Forms
- BEFORE You Start...

ICF wall is quick to erect
Before selecting
and reviewing your plans you should know the following:
1. Insulating Concrete
Form Walls (in most cases) are wider than your wood framed
walls. Because of this most of the outside dimensions on
your plans will change by 4 to 6 inches. (Occasionally dimension
changes are needed for the front entry door in order to allow it to
fit properly between the thicker walls when building with
ICFs).
2. How does the second
floor relate to the first? – If they are not directly on
top of each other, special reinforcing of the structure may be
required. The most ICF friendly house plans are the ones where
floors are on top of each other exactly, due to load bearing
points.
3. Dimensions of length
of the concrete walls should be multiples of 8 inches (in most
cases). This is due to webs being 8 inches apart from each
other and therefore there is less waste when cutting.
4. Windows heights should
correspond to the height of the blocks. For example if the
ICF block is 16 inches high, window heights should be in multiples
of 16 to fit in between the blocks.
5. Look at window
sizes. Family rooms often have most of their outside walls
covered with windows and small pillars in between the windows. You
may have to look at some options that allow for wider columns of
concrete between openings.
6. Locations of windows
and doors – Are the lintel depths and spans
O.K.?
7. Check the
tubs. Again, because of the thicker ICF walls, adjustments
are required where the tub is meant to fit between the two exterior
2 x 4 or 2x6 stud walls.
8. Are there any bay
windows? - The thicker ICF walls may make downsizing of
the windows necessary.
9. The location of the
dryer vent, electrical service, meter locations and any other
openings to the outside walls have to be marked on the
plans. The location should be decided ahead of time
because once the concrete is poured, it is very difficult to
construct the required openings. The location of the Heat Recovery
Ventilator also has to be decided ahead of time. Making 8” holes
through rebar reinforced concrete is a tough task after the
fact.
Building with ICFs:
When building with Insulating
Concrete Forms, an experienced ICF builder, can offer his client
options - to build the entire home from beginning to end, or to
only build the shell from ICFs.
Often clients come to us with
plans that they have pre-selected. They are concerned whether their
plans are suitable for building with ICFs. Can it be built with
ICF’s? This is where only an experienced ICF builder can offer
solid advice for all aspects of building ICF homes.
Every home can be built with
ICFs, but some styles of homes are better suited, and allow ICFs to
perform at their optimum.
Before making the decision to
build with ICFs the homeowner should take the time to review the
entire plan of the home with an experienced ICF builder. Together
they can match the benefits of ICFs with the plan and the rest of
the construction process and materials. A professional can take a
quick look at your plans to see if there are any design issues that
would result in building with Insulating Concrete Forms to be too
expensive or difficult. He can then suggest appropriate changes, if
required.
It is a fact that most potential
ICF customers do quite a bit of research prior to deciding to build
with ICF. We all know the numerous benefits of this type of
building – energy efficiency, strength, sound reduction, water
proof, fire resistant, mold resistant, cleaner air, etc. However,
if your builder is not experienced, the potential problems and
expenses can also be numerous.
Once you know what you are doing,
building the walls is the easy part – the hard part is making sure
all the “pre-work” and decision making has been done in order not
to cause major delays and expenses for the homeowner, and
frustration for both the builder and the homeowner!
See "The Anathomy of an ICF
wall".
More Articles on ICF
Wall:
|